Transcript
Power & Signal Quality TRABTECH
Surge Protection
Arresters for every application
Interference-free mains supply
and signal transmission
A constant power supply and secure data
links are especially important for the
operational reliability of electrical systems,
installations, and devices.
Phoenix Contact meets these requirements
with the comprehensive TRABTECH
product range. Tailored solutions consisting
of surge protection, monitoring, device
circuit breakers, and EMC products ensure
a consistently high power and signal quality
for maximum availability.
Surge protection
Monitoring
Device circuit breakers
EMC solutions
2
PHoENIx CoNTACT
Services
Table of contents
Surge voltages – the underestimated danger
The protective circuit for
safety all round
Page 4
Surge protection for the
power supply unit
Page 6
Surge protection for
measurement and control
technology
Page 12
Surge protection for
information technology
Page 16
Surge protection for
transceiver systems
Page 20
Every day there are more than four million lightning
discharges worldwide.*
Of these, ten percent are considered as ground lightning strikes with surge
currents of up to 200,000 A. In addition to these daily 400,000 discharges
caused by storms, surge voltages also occur within local power grids.
Here, it is switching operations, faults or switched-mode power supply units,
for example, that are responsible.
Regardless of the cause, surge voltages repeatedly lead to unexpected faults in
devices or system failures. TRABTECH surge protection prevents such effects
comprehensively and effectively.
* Source: en.Wikipedia.org > Lightning
Residential buildings, fire
120.000
20.000
60.000
Household contents, fire
330.000
30.000
60.000
Device failure or defects caused by surge voltages are
more frequent than expected. According to the
statistics of German insurers - GDV, this is the most
frequent cause of damage. These figures only apply
to damage that resulted in fire.
Surge voltage
Lightning
Other
Source: GDV Die Deutschen Versicherer 2009
(GDV, the German Insurers 2009)
PHoENIx CoNTACT
3
The protective circuit for safety
all round
The principle of the protective circuit
defines a comprehensive safety measure
against surge voltages. An imaginary circle
encloses devices, plants or systems to be
protected. Surge protection devices that
correspond to the nominal data of the
respective power supply unit or signal type
are to be installed at all points where lines
cut this circle. In order to protect objects
consistently from conductor-specific surge
voltage couplings, the following areas must
be considered:
Power supply
Perfectly coordinated arresters for feeders,
distributors and termination devices guarantee the
power supply.
MCR technology
Optimized arresters are available for different types
of signals and measuring principles.
Information technology
High-speed protection (CAT.6+) for data and
communication technology.
Transceiver technology
This keeps local communication, mobile phones and
satellite or wireless systems on the air whatever
the weather.
4
PHoENIx CoNTACT
PHoENIx CoNTACT
5
Surge protection for the
power supply unit
Efficient protection against surge voltage
always starts in the power supply unit.
A multi-stage protection concept made up
of performance-related lightning current
and surge arresters is considered to be the
most reliable basis.
Protection level, type 1:
High-capacity lightning arresters
Protection level, type 2:
Surge protection, which should not be
missing in any power supply
Protection level, type 3:
Surge protection for sensitive devices
Further arrester combinations are a
sensible addition to the product range.
Plugging instead of
screwing
Universal pluggability
ensures a high degree of
comfort during insulation
measurements in the
system, for example. Instead
of tampering with the
installation, just pull out
the plug.
Whichever way you
turn it
The protective devices of
the compact series can
be installed flexibly. This
avoids unnecessary cable
lengths and offers optimum
protection for any installation
environment.
Status at a glance
Each arrester plug has its
own mechanical display to
display its functional status.
Remote signaling
A common floating PDT
contact makes remote
signaling possible without
taking up extra space.
Regardless of the type of
signal (current, voltage), the
interface can be used as N/C
or N/O contact.
6
PHoENIx CoNTACT
Lightning arrester, type 1
FLASHTRAB compact PLUS:
Powerful spark gap technology for power supply systems
up to 240 / 415 V AC.
• Type 1 lightning arrester with low protection level
• For low-voltage high-current systems with high short-circuiting
power
• For the main power distribution/industrial distribution
• In pre-meter or post-meter area
• At the transition of lightning protection zones LPZ* 0A LPZ 1
• For buildings with external lightning protection
• For buildings with overhead line supply
TN-S / TT systems
TN-C systems
L1
FLT-CP-PLUS-3S-350
Order No. 2882640
L2
L1
L3
L3
N
PEN
L1
FLT-CP-PLUS-2S-350
Order No. 2882666
L2
m
4m
10
8m
4-conductor
system
14
5-conductor
system
m
PE
FLT-CP-PLUS-3C-350
Order No. 2882653
L2
L1
FLT-CP-PLUS-2C-350
Order No. 2882679
L2
PEN
N
L1
FLT-CP-PLUS-1S-350
Order No. 2882682
N
72
mm
3-conductor
system
10
4-conductor
system
8m
m
PE
FLT-CP-PLUS-1C-350
Order No. 2882695
L1
PEN
PE
FLT-CP-PLUS...
IEC category/EN type
Lightning protection level
Nominal voltage UN
Maximum continuous voltage UC
Follow current quenching capacity Ifi
Lightning test current Iimp (10/350)μs
Nominal discharge surge current In (8/20)μs
Protection level Up
Backup fuse max. acc. to IEC 61643-1
...3S-350
...3C-350
mm
36
mm
2-conductor
system
72
3-conductor
system
...2S-350
...2C-350
...1S-350
...1C-350
I / T1
I
100 kA
I
II
II
230/400 V AC ... 240/415 V AC 50/60 Hz
350 V AC 50/60 Hz L-N (L-PEN)
50 kA (264 V AC)
75 kA
75 kA
50 kA
25 kA (per channel)
≤ 1.5 kV
315 A gL/gG
III – IV
III – IV
230 V AC ... 240 V AC 50/60 Hz
50 kA
25 kA
* LPZ: Lightning Protection Zone
PHoENIx CoNTACT
7
Lightning current and surge arresters, type 1 + type 2
FLASHTRAB compact:
Combination of lightning current and surge arresters for
power supply systems up to 240 / 415 V.
• Combined arresters, type 1 and type 2
• For the main power distribution/industrial distribution
• In the post-meter area
• At the transition of lightning protection zones LPZ* 0 LPZ 2
• For buildings with external lightning protection
• For buildings with overhead line supply
TN-S / TT systems
TN-C systems
L1
FLT-CP-3S-350
Order No. 2859712
L2
L1
L3
L3
N
PEN
L1
FLT-CP-2S-350
Order No. 2859767
L2
m
8m
10
4m
4-conductor
system
14
5-conductor
system
m
PE
FLT-CP-3C-350
Order No. 2859725
L2
L1
FLT-CP-2C-350
Order No. 2859770
L2
PEN
N
L1
FLT-CP-1S-350
Order No. 2859738
N
mm
72
8m
3-conductor
system
10
4-conductor
system
m
PE
FLT-CP-1C-350
Order No. 2859741
L1
PEN
FLT-CP-...
IEC category/EN type
Lightning protection level
Nominal voltage UN
Maximum continuous voltage UC
Follow current quenching capacity Ifi
Lightning test current Iimp (10/350)μs
Nominal discharge surge current In (8/20)μs
Protection level Up
Backup fuse max. acc. to IEC 61643-1
* LPZ: Lightning Protection Zone
8
PHoENIx CoNTACT
...3S-350
I
100 kA
...3C-350
...2S-350
...2C-350
I + II / T1 + T2
I
II
II
230/400 V AC ... 240/415 V AC 50/60 Hz
350 V AC 50/60 Hz L-N (L-PEN)
25 kA (264 V AC)
75 kA
75 kA
50 kA
25 kA (per channel)
≤ 1.5 kV
315 A gL/gG
36
mm
2-conductor
system
72
3-conductor
system
mm
PE
...1S-350
...1C-350
III – IV
III – IV
230 V AC ... 240 V AC 50/60 Hz
50 kA
25 kA
Surge arrester, type 2
VALVETRAB compact:
Space-saving surge arresters for all standard power supply
systems up to 240 / 415 V.
• Surge arrester, type 2
• In sub-distribution boards and distribution boxes on the various floors
• Upstream of the residual current circuit breaker
• At the transition of lightning protection zones
LPZ* 0B LPZ 1 / LPZ 1 LPZ 2
• For buildings without external lightning protection
TN-S / TT systems
TN-C systems
L1
VAL-CP-3S-350
Order No. 2859521
L2
L1
VAL-CP-3C-350
Order No. 2859547
L2
L3
L3
N
PEN
L1
VAL-CP-2S-350
Order No. 2859505
L2
36
mm
4-conductor
system
48
5-conductor
system
mm
PE
L1
VAL-CP-2C-350
Order No. 2859589
L2
PEN
N
L1
24
mm
3-conductor
system
36
4-conductor
system
mm
PE
VAL-CP-1S-350
Order No. 2859563
N
VAL-CP-...
IEC category/EN type
Nominal voltage UN
Maximum continuous voltage UC
Nominal discharge surge current In (8/20)μs
Max. discharge surge current Imax (8/20)μs
Protection level Up
Backup fuse max. acc. to IEC 61643-1
24
3-conductor
system
mm
PE
...3S-350
...3C-350
...2S-350
...2C-350
II / T2
230/400 V AC ... 240/415 V AC 50/60 Hz
350 V AC 50/60 Hz L-N (L-PEN)
20 kA (per channel)
40 kA (per channel)
≤ 1.4 kV
125 A gL/gG
...1S-350
230 V AC ... 240 V AC 50/60 Hz
Note: VALVETRAB compact is also available for 120 V power supply systems or as a residual current free variant (VF-type).
* LPZ: Lightning Protection Zone
PHoENIx CoNTACT
9
Surge arrester, type 2 – combined solutions
Combi-RCD*: Surge protection with residual current circuit breaker
FI circuit breaker
(RCD)
Surge arrester
(VAL-CP)
Sensitive for residual currents:
Type A
IEC category/EN type:
II / T2
Rated residual current IΔn:
30 mA/300 mA
Discharge surge current Imax (8/20) μs:
30 kA/path
Release time at IΔn:
≤ 300 ms
Maximum continuous voltage UC:
350 V AC
VAL-CP-RCD-3S/40/0.03
Order No. 2882802
VAL-CP-RCD-3S/40/0.3/SEL
Order No. 2808001
Nominal voltage UN: 230/400 … 240/415 V AC
Nominal load current IL: 40 A
Dimensions (W x H x D): 120 mm x 90 mm x 75 mm
The Combi-RCD combines the properties of a residual current circuit breaker*
and a type 2 surge arrester in a single housing. This innovative “2 in 1” concept
defines an entirely new device type for the simultaneous protection of persons
and devices.
* Residual current device = RCD
72
mm
m
4m
11
13
1.5
mm
Combi-MCB**: Surge protection with a coordinated backup fuse
VAL-CP-MCB-3S-350/40/FM VAL-CP-MCB-3C-350/40/FM VAL-CP-MCB-1S-350/40/FM
Order No. 2882750
Order No. 2882776
Order No. 2882763
IEC category/EN type: II / T2
Nominal voltage UN: 230/400 V AC ... 240/415 V AC
Maximum continuous voltage UC: 350 V AC
Nominal discharge surge current In (8/20) μs: 20 kA/path
Protection level UP: ≤ 2.5 kV
The integrated arrester backup fuses of the VAL-CP-MCB ensure maximum
utilization of the performance capability of the surge protection. Their application
is independent of the operating current fuses of the system – Faults in connection
with fuses for surge protection are thus ruled out.
** Mains Circuit Breaker = MCB
10
PHoENIx CoNTACT
Device protection, type 3
PLUGTRAB
TN-S / TT systems
L1
PLUGTRAB
TN-S / TT / IT systems
L1
L2
N
L3
PE
35
17
.4
.7
mm
mm
N
PE
230 V / 400 V
PT 4-PE/S-230AC/FM
PT ...
Nominal voltage UN
BLOCKTRAB
2858357
2805130
2856812
2800457
2800961
... 2-PE/S-24AC
24 V AC
275 V AC
253 V AC
275 V AC [L-N]
440 V AC [L(N)-PE]
150 V AC
34 V AC / 44 V DC
26 A
1.5 kA (per channel L-N)
4.5 kA (per channel L-N)
≤ 1.2 kV/≤ 1.5 kV
26 A
3 kA
10 kA
≤ 1.1 kV/≤ 1.5 kV
26 A
3 kA
8 kA
≤ 1.2 kV/≤ 1.5 kV
26 A
2.5 kA
10 kA
≤ 620 V/≤ 850 V
26 A
1 kA
2 kA
≤ 180 V/≤ 550 V
22.5 mm
SOCKETTRAB
26.2 mm
N
mm
PE
230 V
.9
mm
42
.9
42
TN-S / TT / IT systems
L1
26.2 mm
N
MAINTRAB
No.
No.
No.
No.
No.
... 2-PE/S-120AC
120 V AC
TN-S / TT / IT systems
230 V
Order
Order
Order
Order
Order
... 2-IT-...
230 V AC
PE
For every commercially
available distribution
box and for 60 mm
deep installation box
2-PE/S-230AC/FM
2-IT-230AC/FM
2-PE/S-120AC/FM
2-PE/S-24AC/FM
2-PE/S-60AC/FM
... 2-PE/S-230AC
230 V AC
22.5 mm
L1
PT
PT
PT
PT
PT
... 4-PE/S-230AC
230 V AC
Maximum continuous voltage UC
Nominal current IN
Nominal discharge surge current In (8/20)μs
Max. discharge surge current Imax (8/20)μs
Protection level Up: L-N / L(N)-PE
230 V
230 V IT
120 V
24 V
60 V
Order No. 2882459
BT-1S 230AC/A
BT-1S-230AC/O
Order No. 2803409 Order No. 2800625
TN-S / TT systems
L1
For every commercially
available flush-type or
cable duct socket
BT-SKT 230/A
Order No. 2859343
COMBITRAB
TN-S / TT systems
L1
N
N
PE
PE
230 V
230 V
Socket attachment plug
combined with antenna
or telecommunication
protection
D, A, NL, N, FIN
... with SAT connection
... with ISDN connection
... with TAE connection
E, P
S, FIN, N
CH
D, A, NL, E, P
B, F, CZ, SVK, PL
Multi-socket strip
combined with TV/SAT
or ISDN protection
MNT-1 D
MNT-TV-SAT D
MNT-ISDN D
MNT-TAE D
MNT-1 E
MNT-1 S/WH
MNT-1 CH II
MNT-POWERLINE
MNT-NET B/F
Order
Order
Order
Order
Order
Order
Order
Order
Order
No.
No.
No.
No.
No.
No.
No.
No.
No.
2882200
2882284
2882336
2882381
2882239
2880862
2882255
2858001
2882226
...with TV-SAT connection
... with ISDN connection
CBT-SCHUKO
Order No. 2857280
CBT-TV-SAT
CBT-ISDN
Order No. 2857303
Order No. 2857316
PHoENIx CoNTACT
11
Surge protection for
measurement and control technology
Signal interfaces are particularly sensitive
to surge voltages. Combined protective
circuits with components which are
powerful and respond quickly are used in
this case.
In addition, the arresters of the
PLUGTRAB family are impressive thanks
to their practical functions. The plug-in
capability of the arresters allows a function
check, even during system operation.
This selection guide helps you find the
right protection quickly and easily in line
with the application – giving you greater
availability.
Forward-looking
monitoring
PLUGTRAB PT-IQ performs
multi-stage monitoring of
all protective devices. A
controller supplies up to
28 devices with voltage and
implements remote signaling.
Permanent installation
Individual DIN rail connectors
can be converted into
a bus using PT-IQ. This
transmits voltage and status
information. Conventional
wiring is not used.
Error-free installation
Voltage keying and protection
against polarity reversal.
Incorrect connection
is not possible.
Space-saving installation
Up to five signal lines can be
protected with one device.
This requires a design width
of just 17.5 mm on the DIN
rail.
12
PHoENIx CoNTACT
Intelligent and systematic surge protection
Grounding
PLUGTRAB PT-IQ is a range of self-monitoring surge protective
devices with multi-stage status indicator. A controller supplies up to
28 protection modules with voltage, collects the status of all connected
protection devices and implements remote signaling via a DIN rail bus
(T-BUS). A surge protective device consists of the plug, base element and
T-BUS adapter.
GND
Indirect grounding
Direct grounding
In the PT…+F-… or
-BE modules, the
connections for the
shield or the reference potential are
connected to the
metal mounting foot
and therefore the
DIN rail via a gasfilled surge arrester.
In the PT-…-UT
or -BE modules,
the connections for
the shield or the
reference potential
are connected to
the DIN rail via the
metal mounting foot.
Floating signal circuits
Controller for
voltage supply
Protection device
Indirect grounding
Direct grounding
Protection for two
double conductors*
e.g., standard signals
0/4 ... 20 mA
PT-IQ-PTB-UT
Order No. 2800768
+
PT-IQ-1x2+F-24DC-UT
Order No. 2800977
PT-IQ-1x2-24DC-UT
Order No. 2800976
Protection for two
double conductors
e.g., standard signals
0/4 ... 20 mA
PT-IQ-PTB-UT
Order No. 2800768
+
PT-IQ-2x2+F-24DC-UT
Order No. 2800981
PT-IQ-2x2-24DC-UT
Order No. 2800980
PT-IQ-PTB-UT
Order No. 2800768
+
PT-IQ-2x1+F-24DC-UT
Order No. 2800788
PT-IQ-2x1-24DC-UT
Order No. 2800787
PT-IQ-PTB-UT
Order No. 2800768
+
PT-IQ-4x1+F-24DC-UT
Order No. 2800983
PT-IQ-4x1-24DC-UT
Order No. 2800982
Signal circuits with common reference potential
Protection for
two conductors*
e.g., binary
switching signals
Protection for
four conductors
e.g., binary
switching signals
* other voltage levels are available > www.phoenixcontact.com
PHoENIx CoNTACT
13
PLUGTRAB PT – plug-in surge protection
PLUGTRAB PT consists of base element and protective plug. Various
different grounding options were implemented via the corresponding
base element. Each protective plug can be tested using the Checkmaster
arrester test device.
Floating signal circuits
The products on this page
support the HART protocol**
Protection for
a double
conductor*
e.g., standard
signals
0/4 … 20 mA
Protection for
two double
conductors*
e.g., standard
signals
0/4 … 20 mA
Plug
Base element
Indirect grounding
Direct grounding
+
PT 1x2+F-BE
Order No. 2856126
PT 1x2-BE
Order No. 2856113
+
PT 2x2+F-BE
Order No. 2839224
PT 2x2-BE
Order No. 2839208
PT 1x2-12DC-ST
Order No. 2856029
PT 1x2-24DC-ST
Order No. 2856032
PT 2x2-12DC-ST
Order No. 2838254
PT 2x2-24DC-ST
Order No. 2838228
Protection for
intrinsically safe
circuits
one or two
double
conductors
PT 2xEX(I)-24DC-ST
Order No. 2838225
+
Protection for
temperature,
2, 3 or 4-wire
measurement
PT 4-24DC-ST
Order No. 2839240
+
Protection for
intrinsically safe
circuits
2, 3 or 4-wire
measurement
PT 4-EX(I)-24DC-ST
Order No. 2839253
+
–
PT 4+F-BE
Order No. 2839415
–
PT 2xEX(I)-BE
Order No. 2839279
PT 4-BE
Order No. 2839402
PT 4-EX(I)-BE
Order No. 2839486
* other voltage levels are available > www.phoenixcontact.com
** HART = Highway Addressable Remote Transducer Protocol (Phoenix Contact is a registered member of the HART Communication Foundation)
14
PHoENIx CoNTACT
Signal circuits with common reference potential
Plug
Protection for
two conductors*
e.g., binary
switching signals
Protection for
four conductors*
e.g., binary
switching signals
Protection for
high signal
voltages*
Base element
PT 2x1-24DC-ST
Order No. 2856074
Indirect grounding
Direct grounding
+
PT 2x1+F-BE
Order No. 2856142
PT 2x1-BE
Order No. 2856139
+
PT 4x1+F-BE
Order No. 2839376
PT 4x1-BE
Order No. 2839363
PT 2x1-24AC-ST
Order No. 2856100
PT 4x1-24DC-ST
Order No. 2838319
PT 4x1-24AC-ST
Order No. 2838351
PT 2x1VA-120AC-ST
Order No. 2839185
+
–
PT 2x1VA-230AC-ST
Order No. 2839198
PT-BE/FM
Order No. 2839282
Single-stage protection with gas-filled arrester as coarse protection
Protection for
two conductors
PT 2-F-ST
Order No. 2859000
+
–
PT-BE/FM
Order No. 2839282
Protection for
four conductors
PT 4-F-ST
Order No. 2858441
+
–
PT 4-BE
Order No. 2839402
Further surge protection devices for measurement and control technology
LINETRAB –
the standard in the
6.2 mm class
SURGETRAB –
Protection directly at the measuring
head
TERMITRAB –
Protection in the modular terminal
block
PHoENIx CoNTACT
15
Surge protection for
information technology
Reliable data exchange and
telecommunication is indispensable
nowadays. Sensitive systems operate at
high frequencies with low signal levels and
expansive networking. Surge voltages would
here result in widespread failures and, in
the worst case, data loss.
65 mm
1
m
00 m
The DATATRAB series can be
used as adapter or DIN rail
module.
25 mm
This selection guide helps you find the
right protection quickly and easily in line
with the application – giving you greater
availability.
The perfect fit
Small and modular
Two-channel protective plug
for CT-TERMIBLOCK and
LSA-Plus strips.
Many applications and
just one solution
Solutions on the basis
of PLUGTRAB series are
especially suitable for
installation in the control
cabinet.
16
PHoENIx CoNTACT
Information and data technology (BUS systems)
Plug
Base element*
Indirect grounding
Direct grounding
PT 3-PB-ST
Order No. 2858030
+
–
PT 1X2-BE
Order No. 2856113
INTERBUS-INLINE remote bus
PT 5-HF-5DC-ST
Order No. 2838762
+
PT 2X2+F-BE
Order No. 2839224
–
INTERBUS-INLINE (I/O)
Analog
PT 2X2-24AC-ST
Order No. 2838283
+
–
PT 2X2-BE
Order No. 2839208
INTERBUS-INLINE (I/O)
Digital
PT 4X1-24AC-ST
Order No. 2838351
+
–
PT 4X1-BE
Order No. 2839363
PT 2XEX(I)-24DC-ST
Order No. 2838225
+
–
PT 2XEX(I)-BE
Order No. 2839279
Profibus DP
Profibus PA
Foundation
Fieldbus
* For an explanation, see page 13 "Grounding"
ETHERNET
(inkl. PoE)
- 100 Base T
- 1000 Base T
- 10G Base T
TOKEN Ring
VG-AnyLAN
DT-LAN-CAT.6+
Order No. 2881007
PROFINET
ETHERNET
- 100 Base T
- 1000 Base T
TOKEN Ring
D-LAN-19“-24
Order No. 2838791
D-LAN-19“-16
Order No. 2880147
High-speed data protection
The DATATRAB family is synonymous with
effective surge protection for high-speed
data transfers.
Accessories
RJ45 patch cable, length: 0.5 m
FL CAT6 PATCH 0,5
Order No. 2891288
RJ45 patch cable, length: 3 m
FL CAT6 PATCH 3,0
Order No. 2891686
As a result, the DT-LAN-CAT.6+ provides
universal protection for network speeds
up to 10 Gbps without influencing the
signals.
PHoENIx CoNTACT
17
Data technology (serial interfaces)
Plug
Base element
Indirect grounding
Direct grounding
Data systems
RS 485
RS 422A
PT 5-HF-12DC-ST
Order No. 2838775
+
PT 2X2+F-BE
Order No. 2839224
–
Data systems
RS 232 C
PT 3-HF-12DC-ST
Order No. 2858043
+
PT 1X2+F-BE
Order No. 2856126
–
Telecommunications
ADSL, HDSL, T-DSL, V-DSL
Analog telephony
ISDN UK0
PT 2-TELE
Order No. 2882828
ADSL, HDSL, T-DSL, V-DSL
Analog telephony
ISDN UK0
ATM
ISDN S0
ISDN S2M
Analog telephony
Coarse protection with fail-safe contact
Analog telephony
Coarse protection with fail-safe contact and
power cross protection
Analog telephony
Coarse and fine protection
18
PHoENIx CoNTACT
DT-TELE-RJ45
Order No. 2882925
DT-LAN-CAT.6+
Order No. 2881007
CTM 2X1-180DC-GS
Order No. 2838636
CTM 2X1-180DC-GS-P
Order No. 2838623
CTM 1X2-110AC
Order No. 2838539
RS 485
DT-UFB-485/BS
Order No. 22920612
RS 232 C / V.24
with D-SUB 9 connection
DT-UFB-V24/S-9-SB
Order No. 2803069
RS 232 C / V.24
with adapter cable from D-SUB 9 on D-SUB 25
DT-UFB-V24/S-SB-SET
Order No. 2803072
ADSL/T-DSL
- Up to 16,000 kbps
Analog telephony
CTM 1X2-110AC
Order No. 2838539
ISDN UK0
ISDN S0
ISDN S2M
CTM ISDN
Order No. 2838555
Accessories
Magazine with grounding rail
- To accommodate up to 10 CTM connectors
CTM 10-MAG
Order No. 2838610
Disconnect strip screw terminal block
- For standard rails of type NS-32 and NS-35/7.5
- compatible with the CTM 10-MAG with connections for 20 conductors up to 4 mm2 and
with disconnect contacts for CTM protective connectors
CT-TERMIBLOCK 10DA
Order No. 0441711
PHoENIx CoNTACT
19
Surge protection for
transceiver systems
The high frequencies of wireless
transmission require the use of protective
devices with reduced insertion attenuation.
COAXTRAB fulfills this requirement.
The coaxial arresters are suitable for all
common transmission systems in mobile
and public safety wireless networks in the
field of video or television transmission.
Customized products
Thanks to their very low
attenuation values, surge
protection devices ensure
interference-free signal
transmission in all standard
applications.
Shielding
Good shielding properties are
indispensable for a “clean”
transmission. Robust metal
housings ensure a perfect
shielding and are suitable for
use in harsh environments.
Connection technology
A connection system suitable
for the relevant application:
F and N connector,
TV connector and 7/16,
UHF, BNC connections.
Many applications and
just one solution
Solutions on the basis
of PLUGTRAB series are
especially suitable for
installation in the control
cabinet.
20
PHoENIx CoNTACT
Protection for transceiver systems
GPS or
GSM (900, 1800 MHz)
UMTS
- With N connector
GPS or
GSM (900, 1800 MHz)
UMTS
CN-UB-280DC-SB
Order No. 2818148
CN-UB-280DC-BB
Order No. 2818850
C7/16-UB-280DC-SB-SET
Order No. 2881544
- With 7/16 connector
GSM (900, 1800, 1900 MHz)
UMTS
CN-LAMBDA/4-2.25-BB
Order No. 2801057
- Without supply voltage on the coaxial cable
- Very low protection level
- With N connector
CN-LAMBDA/4-2.25-SB
Order No. 2801056
GSM (900, 1800, 1900 MHz)
UMTS
C7/16-LAMBDA/4-2.25-BB
Order No. 2801060
- Without supply voltage on the coaxial cable
- Very low protection level
- With 7/16 connector
C7/16-LAMBDA/4-2.25-SB
Order No. 2801059
WiMAX (2.4... 6 GHz)
CN-LAMBDA/4-5.9-BB
Order No. 2838490
- Without supply voltage on the coaxial cable
- Very low protection level
- With N connector
CN-LAMBDA/4-5.9-SB
Order No. 2800023
Accessories
Mounting plate
- For individually securing the CN-UB-280DC
Mounting plate, 90° angled
- For individually securing the CN-UB-280DC e.g. for wall mounting
CN-UB/MP
Order No. 2818135
CN-UB/MP-90DEG-50
Order No. 2803137
PHoENIx CoNTACT
21
Protection for video monitoring systems
50 Ohm
C-UFB-5DC/E
Order No. 2782300
75 Ohm
C-UFB-5DC/E 75
Order No. 2763604
with BNC connection
for one video signal
PT 3-PB-ST
Order No. 2858030
PT 1X2+F-BE
Order No. 2856126
with screw connection
for two video signals
PT 2X2-HF-5DC-ST
Order No. 2839567
PT 2X2-BE
Order No. 2839208
SAT-MULTISWITCH
Protection for television and radio systems
SAT-MULTISWITCH
Satellite television
Upstream of the distributor
(multiswitch)
Satellite television
P 125
Mo 21.05.- 17.23
DIGITALSAT-RECEIVER
Upstream of the SAT
receiver or television
Cable/terrestrial
television
Power
NDR
NDR
DR 2
1
2
3
4
5
6
7
8
9
Power
Traack 1
Tra
12
2
03:
0
3:2
3:
24
Power
prog
Power
Vol
Vo
olu
ume:
ume
m : 23
23
ssou
ource
ce
e: CD
CD
Phones
Tuner
Aux1
Aux2
Tape1
Tape2
CD
Phono
Upstream of the television,
radio or tuner of the
HiFi system
C-SAT-BOX
Order No. 2880561
C-TV-SAT
Order No. 2856993
C-TV/HIFI
Order No. 2857002
Accessories
F connector adapter (plug-to-plug)
- Ideal for direct connection of the C-SAT-BOX to a multiswitch with the same pitch
- No thread plug-in coupling allows a quick connection
ADAPTER KOAX TYP F
Order No. 2880972
- Secure hold via clamping ring
F connector cable (connector to connector)
- For flexibly connecting the C-SAT-BOX to a multiswitch with a different pitch
22
PHoENIx CoNTACT
KBL-SAT/20
Order No. 2880985
Combined protection for television/radio connections and the power supply unit
Satellite television
Country: D, A, NL
Use with simultaneous protection of power supply
upstream of the SAT receiver or television.
MNT-TV-SAT D
Order No. 2882284
MNT-TV-SAT D/WH
Order No. 2882297
Country: B, F, CZ, SVK,
PL
MAINTRAB
MNT-...
MNT-TV-SAT B/F
Order No. 2882307
Country: E, P
MNT-TV-SAT E
Order No. 2882310
Country: S, FIN, N
MNT-TV-SAT S/WH
Order No. 2880888
P 125
Mo 21.05.- 17.23
DIGITALSAT-RECEIVER
COMBITRAB
CBT-...
Country: D, I, NL, E, P
CBT-TV-SAT
Order No. 2857303
Cable/terrestrial television
Country: D, A, NL
Use with simultaneous protection of power supply
upstream of the television, radio or tuner of the
HiFi system.
MNT-TV-SAT D
Order No. 2882284
MNT-TV-SAT D/WH
Order No. 2882297
Country: B, F, CZ, SVK,
PL
MAINTRAB
MNT-...
MNT-TV-SAT B/F
Order No. 2882307
Country: E, P
MNT-TV-SAT E
Order No. 2882310
Country: S, FIN, N
MNT-TV-SAT S/WH
Order No. 2880888
Power
ND
NDR
DR
R 2
1
2
3
4
5
6
7
8
9
Power
Traack 1
Tra
12
2
03:
0
3:2
3:
24
Power
prog
Power
Vol
Vo
olu
ume:
ume
m : 23
23
ssou
ource
ce
e: CD
CD
Phones
Tuner
Aux1
Aux2
Tape1
Tape2
CD
Phono
COMBITRAB
CBT-...
Country: D, I, NL, E, P
CBT-TV-SAT
Order No. 2857303
PHoENIx CoNTACT
23
Further information on the products
presented here and on the world of solutions
from Phoenix Contact can be found at
www.phoenixcontact.net/catalog
Modular Terminal Blocks
CLIPLINE 1
Marking Systems, Tools, and
Mounting Material
CLIPLINE 2
Or contact us directly.
Connection Technology for
Field Devices and Field Cabling
PLUSCON
INTERFACE
Automation Components
and Systems
AUTOMATION
PHOENIX CONTACT GmbH & Co. KG
32823 Blomberg, Germany
Phone: +49 (0) 52 35 3-00
Fax:
+49 (0) 52 35 3-4 12 00
www.phoenixcontact.com
Printed in Germany
Signal Converters, Switching Devices,
Power Supply Units
MNR 52005654/10.04.2012-01
Power and Signal Quality
TRABTECH
© PHOENIX CONTACT 2012
Device Connection Technology
and Electronic Housings
COMBICON